Question: Does R Wire Go To RH Or RC?

Do I need a jumper from R to RC?

If your system has both heating and cooling functions, you’ll need to connect both the Rc and Rh terminals with a red wire.

Because many thermostats come with a pre-installed thermostat jumper wire that connects these terminals, you only need one red wire, which could be the thermostat Rc wire or the Rh wire..

What is the difference between R and RC on a thermostat?

Rh stands for Red-Heat and Rc stands for Red-Cool. If you only have a single red wire the jumper between Rh and Rc are required for some heating and cooling hybrid systems depending on your thermostat.

Is RC the same as C wire?

Though it is a common notion, it may be incorrect to state that the C-wire powers the thermostat. Typically, the wires that give the power supply (usually termed as the ‘hot’ wires) are marked Rc (for cooling) and Rh (for heating). … ‘ If your system has a common wire, it will be marked ‘C’ at most times.

Should RC and RH be connected?

The RC wire (C for Cooling), if connected properly, controls your HVAC cooling. The RH wire (H for Heating) provides power to your HVAC heating. If you are planning to replace your home thermostat, it will be essential that you know which wires to connect to the right terminals in your thermostat.

What if there is no C wire for thermostat?

If your current thermostat didn’t need a C-wire, it (or a wire that can be used as a C-wire) might be rolled up inside the wall.

Where does Rh wire go on thermostat?

The Rh wire connects to your heating system as opposed to your cooling system. This wire may be red without an “H” attached to it, depending on if you have a dual transformer setup. The Rh wire connects to the RH terminal on your thermostat.

Whats the difference between RC and RH?

The RH wire refers to “red heating” which means that this is the connection you need in order to power the heating system of your air conditioning unit. … The RC wire, on the other hand, refers to “red cooling”. It’s the same with the RH wire in that it powers the thermostat. For the RC, it powers the cooling system.

What is jumper wire used for?

A jump wire (also known as jumper wire, or jumper) is an electrical wire, or group of them in a cable, with a connector or pin at each end (or sometimes without them – simply “tinned”), which is normally used to interconnect the components of a breadboard or other prototype or test circuit, internally or with other …

What is the color code for wiring a thermostat?

Thermostat Wiring Color Code ChartMarkingWire Color CodeDescriptionRcRedPower from cooling, 24 Vac transformerRhRedPower from heat, 24 Vac transformerCBlack/BlueCommon of 24 Vac transformerWWhitePrimary heat cell relay12 more rows

What happens if you wire a thermostat wrong?

Electric shock. Blowing a circuit breaker. Damaging the thermostat unit, the electrical system or even the AC/furnace unit itself. Dual-fuel systems, a poorly located thermostat, whole-home humidifiers, or incorrect wiring can make the installation of a thermostat a longer, more frustrating, and more complicated …

What does W mean on a thermostat?

heat loadW=the heat load. On a call for heating the thermostat closes a switch between R and W, sending 24v to energize the heating circuit. Y= the cool load. On a call for cooling the thermostat closes a switch between R and Y, sending 24v to energize the cooling circuit. G= the fan load.

What does R and RC mean on thermostat?

R – 24vac (Heating transformer) Rc – 24vac (Cooling transformer) *Trade model thermostats are required to operate “dual-fuel” systems (systems that use a heat pump for the first 1 or 2 stages of heating and use a gas or oil furnace for backup / emergency heating).

What is the Rh wire on the Nest thermostat?

Nest often has a sub base issue. Usually the issue is contained to the cooling side. Rh is power input for the heating side.

Why is there a jumper between R and RC?

Effectively there isn’t a second RH wire, although there is an RH terminal. However, the heating still needs to be controlled, so a wire known as a jumper is connected between the RC and the RH terminals so that power gets to the heating control part of the thermostat.

How many wires does a Nest thermostat need?

two wiresTake two wires from the wire bundle that goes to the current thermostat and attach them to the T1 and T2 terminals on the Heat Link.

What does RC and RH mean on a thermostat?

RC: The RC terminal is the 24-volt cooling power supply. RH: The RH terminal is the 24-volt heating power supply. (Note: The RC and RH terminals are jumpered together in a four-wire heat/cool system and a single-stage heat pump system, but not in a five-wire heating/cooling system.)